|
|
@@ -0,0 +1,133 @@
|
|
|
+# 默认工位配置
|
|
|
+
|
|
|
+#单工位
|
|
|
+station:
|
|
|
+ mode: single
|
|
|
+ name: 液冷板安装+激光点固
|
|
|
+ stations:
|
|
|
+ - code: OP150C
|
|
|
+ line_sn: XT
|
|
|
+
|
|
|
+##双工位
|
|
|
+#station:
|
|
|
+# mode: single
|
|
|
+# name: 总成正面装配
|
|
|
+# stations:
|
|
|
+# - code: OP140A
|
|
|
+# line_sn: XT
|
|
|
+
|
|
|
+server:
|
|
|
+# ip: 127.0.0.1
|
|
|
+ ip: 192.168.110.99
|
|
|
+ tcp_port: 3000
|
|
|
+ http_port: 8980
|
|
|
+ heart_beat_cycle: 60
|
|
|
+
|
|
|
+workflow:
|
|
|
+ #手动模式
|
|
|
+# submit_mode: manual
|
|
|
+# 自动模式
|
|
|
+ submit_mode: auto
|
|
|
+
|
|
|
+ steps:
|
|
|
+# - id: read_device_data
|
|
|
+# name: 读取设备数据
|
|
|
+ - id: scan_product
|
|
|
+ name: 扫描工件码
|
|
|
+ config:
|
|
|
+ prefix: "+KB24" # 工件码前缀校验
|
|
|
+ - id: check_quality
|
|
|
+ name: 质量检查
|
|
|
+ # 质量检查用的工艺号 如果在bind_material则是物料绑定用的工艺号不填有默认值
|
|
|
+ craft: "100000"
|
|
|
+ - id: scan_material
|
|
|
+ name: 扫描冷板码
|
|
|
+ config:
|
|
|
+ label: 冷板码
|
|
|
+ prefix: "+KA94" # 冷板码前缀校验
|
|
|
+ - id: validate_material
|
|
|
+ name: 校验冷板码
|
|
|
+ config:
|
|
|
+ craft: "400004" # 冷板校验用的工艺号
|
|
|
+
|
|
|
+# - id: scan_material
|
|
|
+# name: 扫描底护板码
|
|
|
+# config:
|
|
|
+# label: 底护板码
|
|
|
+# prefix: "+KB77" # 底护板码前缀校验
|
|
|
+# - id: validate_material
|
|
|
+# name: 校验底护板码
|
|
|
+# config:
|
|
|
+# craft: "400004"
|
|
|
+
|
|
|
+# - id: start_heartbeat
|
|
|
+#
|
|
|
+# - id: reset_device_count
|
|
|
+# name: 重置设备计数
|
|
|
+# config:
|
|
|
+# address: 8
|
|
|
+# value: 1
|
|
|
+# clear_addresses:
|
|
|
+# - address: 66
|
|
|
+# value: 0
|
|
|
+# - address: 68
|
|
|
+# value: 0
|
|
|
+# - address: 70
|
|
|
+# value: 0
|
|
|
+#
|
|
|
+# - id: wait_device_complete
|
|
|
+# - id: stop_heartbeat
|
|
|
+
|
|
|
+ - id: upload_result
|
|
|
+ name: 上传结果
|
|
|
+# craft: "500002" # A枪用500001，B枪的包改成500002
|
|
|
+ - id: reset_station
|
|
|
+ name: 重置工位
|
|
|
+
|
|
|
+device:
|
|
|
+ enabled: false
|
|
|
+ type: modbus_tcp
|
|
|
+ connect_timeout: 3000
|
|
|
+
|
|
|
+ connections:
|
|
|
+ - station_index: 0
|
|
|
+ ip: 192.168.0.6
|
|
|
+ port: 502
|
|
|
+# - station_index: 1
|
|
|
+# ip: 192.168.0.16
|
|
|
+# port: 502
|
|
|
+ timeout_enabled: true #预留但未实现的配置项
|
|
|
+ heartbeat_address: 4160
|
|
|
+ ready_signal_address: 8
|
|
|
+ complete_condition:
|
|
|
+ type: count
|
|
|
+
|
|
|
+ # 拉铆过程参数采集配置（从PLC读取，通过HTTP上传到MES）
|
|
|
+ prod_params:
|
|
|
+ enabled: false
|
|
|
+ # PLC寄存器地址（Int32，读取后除以1000得到实际值）
|
|
|
+ fout_address: 4112 # 力输出值 F-out
|
|
|
+ sout_address: 4120 # 行程输出值 S-out
|
|
|
+ fmin_address: 4116 # 力最小值 F-min
|
|
|
+ smin_address: 4126 # 行程最小值 S-min
|
|
|
+ fmax_address: 4114 # 力最大值 F-max
|
|
|
+ smax_address: 4124 # 行程最大值 S-max
|
|
|
+ qty_address: 4 # 数量寄存器地址（Int16）
|
|
|
+ upload_interval: 60 # 上传间隔（秒）
|
|
|
+ui:
|
|
|
+# 设备信息行配置（最多2行）
|
|
|
+# label: 可选前置标签，不配就不显示
|
|
|
+# preset_address: 预设数量寄存器地址
|
|
|
+# finished_address: 完成数量寄存器地址
|
|
|
+ device_info_rows:
|
|
|
+ - label: "A"
|
|
|
+# connection_index: 0
|
|
|
+# preset_address: 4534
|
|
|
+# finished_address: 66
|
|
|
+# - label: "B"
|
|
|
+# connection_index: 1
|
|
|
+# preset_address: 4534
|
|
|
+# finished_address: 66
|
|
|
+# 绑定物料
|
|
|
+ show_material_input: true
|
|
|
+ material_label: 冷板码
|
